大数跨境

地基处理|美标地基强夯技术简介

地基处理|美标地基强夯技术简介 惯性出海
2022-11-10
0
导读:美标地基强夯技术简介


Dynamic Compaction | Deep Compaction

下文为翻译件,原文放在文末,感兴趣的可以学习查看


Luis Menard 在 1960 年代中期开发了动力夯实 (DC)技术,也称为动力深度夯实。然而,据称该技术在一千多年前就已使用。在这种地基处理技术中,通过吊起将重物砸在地面上以将土壤夯实至 40 英尺(12.5 米)的深度。

该技术可用于减少地基沉降、减少地震沉降和液化可能性、允许在回填土、密实垃圾堆、采矿弃土上进行开发,同时减少可塌陷土壤中的沉降。

  • 强夯适用土壤类型

最适合动态压实的土壤类型是颗粒状、可渗透的土壤。在粘性土壤中,压实能量往往被细小的土壤颗粒吸收,从而降低了该技术的有效性。表 1 显示了各种地质类型的处理预期。

表 1:强夯的处理预期和所需能量(Hussin,2006)

请注意,对于上面的表 1,能量 =(吊锤高度 x 重量 x 夯实次数)/待压实的土壤体积; 1 吨 ft/ft3 = 94.1 kJ/m3。


为了处理成功,地下水位必须至少低于工作面 6 英尺(1.8 米)。在有机质土壤中,强夯过程通过不断填充砂石来穿透相关土层。


  • 设备

尽管已经制造了专门设计的钻机,但通常使用循环式起重机来减轻重量。标准起重机通常不是为处理高循环动态载荷而设计的,因此为了保持安全的工作环境,起重机必须处于良好状态,并在执行操作时不断进行维护和检查。


起重机通常设置有足够的吊杆以将重物从 50 到 100 英尺(15.4 到 30.8 m)的高度落下,并且只有一根绳索使其几乎“自由落体”,从而最大限度地提高重物撞击土壤的力。要降低的重量必须小于起重机和电缆的安全单线能力。通常重量范围为 10 至 30 吨(90 至 270 kN),由钢制成,可承受重复的动态力。


  • 施工步骤

反复举起和放下重物直到它砸到地面是强夯的主要技术。主要下降位置通常布置在 10 到 20 英尺(3.1 到 6.2 米)的网格中,次要通道放置在每个主要通道的中点。在该位置进行后续降落之前,一旦达到 3 到 4 英尺(约 1 m)的深度,夯坑就会充满颗粒材料。


操作会产生较大的土壤振动,这可能会对周围的现有结构产生负面影响。特别是,应检查预期夯实位置 500 英尺(154 米)范围内的结构的振动敏感性及其先前条件。在进行强夯时监测振动也是可取的。如果打算在现有结构的 200 英尺(61.5 米)范围内进行强夯,则应格外小心并密切观察。


  • 材料

通常使用干净、自由排水的粒状土来填充作业留下的陨石坑。沙质土壤可以使用由沙子制成的回填土进行处理。细粒土壤或垃圾填埋场经常用碎石回填土处理。


  • 设计

对拟议建设和当前地下条件的检查将作为设计的起点(承载能力、沉降、液化等)。然后使用具有改进的土质特性(例如,SPT N 值等)的相同研究确定提供所需性能所需的最小值。下一步是计算提供所需性能所需的改良土壤的垂直和横向范围。


施加到地面的单次夯击能量的平方根(重量乘以落锤高度)决定了效果的深度。罗伯特·卢卡斯博士使用现场收集的数据创建了如下所示的相关性:


D = k(W x H)^0.5


此处:

D是地表以下的最大影响深度,以米为单位,

W 是落锤的重量,以公吨 (9 kN) 为单位,并且

H 是地面以上的落锤高度,以米为单位。

常数 k 随土壤类型而变化,介于 0.3 和 0.7 之间,细粒土壤的值较低。


尽管这种方法预测的最大改进深度在上三分之二,但处理效果会逐渐减小,直到在基地三分之一处达到零。在该区域内获得的改进程度通过在同一地点反复进行打击而增加。然而,当改善率下降时,效果就会大幅下降。


表 1 列出了实现这一目标所需的预期单位能量范围。回填处理有助于最大限度地减少空隙,但对未来的生物降解影响最小。因此,回填处理通常只允许在指定用于规划的道路和人行道的区域进行,而不是用于结构。完成强夯后,土壤在距离地表 3 到 4 英尺 (1 m) 范围内是松散的。一个低能量的“熨烫通道”,通常需要在整个表面区域从 10 到 15 英尺(3.0 到 4.5 米)的高度下降相同的重量,用于压实地表土壤。


  • 质量控制和质量保证

大多数施工程序都使用SPT来评估改进。SPT在回填场地中具有挑战性,但是可以使用填土堆或剪切波速度测试进行大规模荷载试验。为了衡量取得的进展并进行必要的调整,可以在项目开始时处理一个测试区域。为了识别需要更多处理的场地“软”部分,还可以测量夯坑的深度。伴随进一步锤击穿透深度的下降可以视为处理到位的一个信号。




 现场图


以下为英文原文可上下滑动:

Dynamic Compaction | Deep Compaction

Luis Menard developed dynamic compaction (DC), also known as dynamic deep compaction, in the middle of the 1960s. However, there are claims that the technique was used more than a thousand years before. In this ground improvement technique, a heavy weight is dropped on the ground’s surface to compact soils to depths of up to 40 feet (12.5 metres).

The technique is utilised to reduce settlements in foundations, reduce seismic subsidence and liquefaction potential, permit development on fills, densify refuse dumps, enhance mining spoils, and reduce settlements in collapsible soils.


  • Applicable Soil Types for Dynamic Compaction

The most suitable types of soil for dynamic compaction are granular, permeable soils. In cohesive soils, the compaction energy tends to be absorbed by fine soil particles, which reduces the technique’s effectiveness. Table 1 shows the anticipated improvement for various soil types. 

Table 1: Expected Improvement and Required Energy with Dynamic Compaction (Hussin, 2006)

Note that for Table 1 above, Energy = (drop height x weight x number of drops)/soil volume to be compacted; 1 ton ft/ft3 = 94.1 kJ/m3.


For the procedure to be successful, the groundwater table must be at least 6 feet (1.8 metres) below the working surface. Sand or stone columns have been built using dynamic compaction in organic soils by repeatedly filling the crater with the material and forcing the column through the organic layer.


  • Equipment

Although specifically designed rigs have been made, the weight is typically dropped using a cycle-duty crane. Standard cranes are often not designed to handle high-cycle dynamic loading, so in order to maintain a safe working environment, the cranes must be in good condition and constantly maintained and inspected while performing the operation.


Typical weight for dynamic compactionTypical weight for dynamic compaction

The crane is often set up with enough boom to drop the weight from heights of 50 to 100 ft (15.4 to 30.8 m) and only one rope to let it almost “free fall,” maximising the force of the weight hitting the soil. The weight to be lowered must be less than the crane’s and cable’s safe single-line capability. Typically weights range from 10 to 30 tons (90 to 270 kN) and are constructed of steel to withstand the repetitive dynamic forces.


  • Procedure

Lifting and dropping a weight repeatedly till it hits the ground surface is the major technique for dynamic compaction. The primary drop locations are normally laid out in a grid of 10 to 20 feet (3.1 to 6.2 metres), with a secondary pass placed at each of the primary pass’s midpoints. Prior to doing subsequent drops at that place, the crater is filled with granular material once it has reached a depth of 3 to 4 ft (about 1 m).

Large soil vibrations are generated by the operation, which may negatively affect surrounding existing structures. In particular, structures within 500 feet (154 metres) of the locations of the intended drops should be examined for their vibration sensitivity and their antecedent conditions. Monitoring the vibrations when carrying out dynamic compaction is also advisable. If dynamic compaction is intended to be carried out within 200 feet (61.5 metres) of an existing structure, extreme caution and close observation should be made.


  • Materials

A clean, freely draining granular earth is often used to fill the craters left behind by the operation. Sandy soils can be treated by using a backfill made of sand. Finer-grained soils or landfills are frequently treated with a crushed stone backfill.


  • Design

An examination of the proposed construction and the current subsurface conditions will serve as the starting point for the design (bearing capacity, settlement, liquefaction, etc.). The minimal values required to deliver the required performance are then determined using the same study with the improved soil characteristics (e.g., SPT N value, etc.). The next step is to calculate the vertical and lateral extent of improved soil required to deliver the desired performance.


The square root of the energy from a single drop (weight times drop height) applied to the ground surface determines the depth of the effect. Dr. Robert Lucas created the correlation shown below using data collected in the field:


D = k(W x H)^0.5

where;

D is the maximum influence depth in meters beneath the ground surface,

W is the weight in metric tons (9 kN) of the object being dropped, and

H is the drop height in meters above the ground surface.

The constant k varies with soil type and is between 0.3 and 0.7, with lower values for finer-grained soils.


Even though the largest depth of improvement predicted by this method is in the upper two-thirds, the improvement gradually decreases until it reaches zero in the bottom third. The degree of improvement attained within this zone is increased by landing strikes repeatedly at the same spot. However, when the rate of improvement falls, there comes a moment when the benefits become less valuable.


Table 1 lists the anticipated range of unit energy needed to reach this goal. Treatment of landfills is helpful in minimising voids, but it has minimal impact on the biodegradation of components in the future. As a result, treatment of landfills is normally only allowed in areas designated for planned roadways and pavement, not for structures. The soils are loose within 3 to 4 feet (1 m) of the surface once dynamic compaction is finished. A low-energy “ironing pass,” which typically entails dropping the same weight from a height of 10 to 15 feet (3.0 to 4.5 metres) over the entire surface area, is used to compact the surface soils.


  • Quality control and quality assurance

Penetration testing is used in the majority of applications to evaluate improvement. Penetration testing is challenging in construction waste or landfills, however large-scale load experiments using fill mounds or shear wave velocity tests can be carried out. To measure the progress made and make necessary adjustments, a test area might be treated at the start of the programme. To identify “soft” sections of the site that need more treatment, the depth of the craters can also be measured. When adequate improvement is attained, the decrease in penetration with further drops serves as a signal.


References

Hussin J. D. (2006): ‘Methods of soft ground improvement’ in ‘The Foundation Engineering Handbook’ Edited by Gunaratne M. Taylor and Francis USA.


往期精彩合集点击



END


关于本号

转载须知

转发,评论,右小角点赞或点击在看,可获得《牛津建筑大辞典》电子版一份

【声明】内容源于网络
0
0
惯性出海
1234
内容 104
粉丝 0
惯性出海 1234
总阅读0
粉丝0
内容104